background image

Skillmill:

Technical Service Guide - Rev. 2.2

Page 25

e-mail: 

[email protected]

3.  OPERATING PRINCIPLE

For the wiring diagram please refer to the one included in the paragraph: 

“2.7 Wiring diagrams” 

on page 19

.

3.1  ELECTRONIC COMPONENTS

3.1.1  VOLTAGE CONVERTER (POWER SUPPLY)

The voltage converter receives the high voltage and transforms it into low voltage (5 V). It can sup-

ply a maximum current of 2 A to power all the equipment electronics (display, angle sensor, RPM 

sensor and NFC).
It is equipped with 4 different sockets based on the necessary standard.
In the CONNECT version, it is connected to the Low Kit and, through it, supplies power to all the 

equipment's electronic components.
In the CORDLESS version, it is used to re-charge the battery when necessary.

3.1.2  DISPLAY (CONNECT VERSION)

It is powered with 5 V voltage, received from the Low Kit. It can be powered using the mini USB 

port that is present, connecting a PC or specific USB power supply.
If powered via the mini USB port, when the equipment is turned on it is possible to see 3 buttons on 

the display that are normally hidden, and a heart shaped icon. These are used, in different combi-

nations, to access the display's configuration menu. For details, refer to the paragraph: 

“6.4 Display 

configuration (Connect version)” on page 48

.

The display is equipped with a Wi-Fi board.
When powered, the CPU is always on even if the display seems off.
The display is managed by SW that can be updated.
If the display is replaced, the QR Code sticker must be replaced.

3.1.3  DISPLAY (CONSOLE VERSION)

In comparison to the Connect version display, the Console version display does not include the 

following:

• 

WI-FI technology;

• 

Display backlighting;

• 

Keyboard backlighting;

• 

Heart button not illuminated, drawn.

Summary of Contents for Skillmill Console













































































Reviews: