Tatu Marchesan STP2 Instruction Manual Download

Page: 46 / 50

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

STP²

Maintenance

Lubrication

NOTE

In order to reduce the wearing caused by the friction in the moving parts of the

equipment, it is necessary to make a correct lubrication, as indicated below:

• Be certified about the lubricant quality, with relation to its efficiency and purity,

avoiding the use of products contaminated by water, earth and others.

• Use medium consistency grease.
• Remove the remainder old grease around the articulations.
• Clean up all the grease fittings with a cloth before introducing the lubricant and

replace the defective ones.

• Introduce an enough amount of new grease.

Lubricate every 10 working hours

Special attention should be given to the lubricant intervals on the different

points of the planter.

Summary of Contents for STP2



















































Search results

Summary of Contents for STP2

Reviews:

Related manuals for STP2

Brands by name

Popular brands

Tatu Marchesan STP2, Instruction Manual

Search results

Summary of Contents for STP2

Reviews:

Related manuals for STP2

Brands by name

Popular brands