Tally T6215 Maintenance Manual Download Page 80

Page: 80 / 164

T6215 Maintenance Manual

4–10

Step 6. Slide the upper left tractor as far to the left as it will go. Lift the Hammer

ank

and shuttle out of the printer, being careful not to damage the ribbon shield.

Hammer Bank

and attached

Shuttle

Figure 12. Lifting Hammer

ank from printer.

When reinstalling the Hammer

ank, install and tighten the retainer clips (Step

4), before installing and tightening the KEPS nuts (Step 5).

When reinstalling the Shuttle Drive belt (Step 3), press the belt against the
lower shuttle motor pulley with one hand, and "roll" the belt onto the upper
shuttle pulley.

Shuttle Drive Belt

Reach underneath
and hold belt.

Roll belt onto pulley

with other hand.

Figure 13. Replacing Shuttle Drive belt.

Summary of Contents for T6215





































































































































































Search results

Summary of Contents for T6215

Reviews:

Related manuals for T6215

Brands by name

Popular brands

Tally T6215, Maintenance Manual

Search results

Summary of Contents for T6215

Reviews:

Related manuals for T6215

Brands by name

Popular brands