Tally T6215 Maintenance Manual Download Page 101

Page: 101 / 164

4–31

Chapter 4:

Removing and Replacing Components

Procedure 16: Tractor Phasing/Paper Drive Belt Tension Adjustment

Any time that a tractor paper drive pulley or drive belt is removed or if the
paper drive motor is replaced, the paper system must be checked for proper
phasing and belt tension.

Step 1. Remove Ribbon Platform (see Procedure 1).

Step 2. Tilt the Print Mechanistm (see Procedure 10).

Step 3. Loosen the screw holding the lower idler bracket and slide it away from the

belt, then retighten the screw to hold the bracket in place temporarily.

Paper Drive Motor

Screws,

3 places

Lower Drive Belt

Idler Bracket

Upper Drive Belt

Side Frame Plate

Figure 33. Tractor phasing and paper drive belt.

Step 4. Loosen the three screws holding the paper drive motor to the side frame

plate.

Step 5. With the lower drive belt installed, slide the motor up as far as possible.

Retighten one screw to hold the motor in place.

Summary of Contents for T6215





































































































































































Search results

Summary of Contents for T6215

Reviews:

Related manuals for T6215

Brands by name

Popular brands

Tally T6215, Maintenance Manual

Search results

Summary of Contents for T6215

Reviews:

Related manuals for T6215

Brands by name

Popular brands