Tally T6215 Maintenance Manual Download Page 76

Page: 76 / 164

T6215 Maintenance Manual

4–6

Procedure 4: Control Panel Removal

Step 1. Remove the Ribbon Platform.

Step 2. Reach underneath the Control Panel assembly and unplug the gray Control

Panel cable.

Control P

anel

Unplug Control Panel Cable

Figure 6. Unplugging Control Panel cable.

Step 3. Loosen the four screws underneath the Control Panel at the bottom edge of

the frame.

Step 4. Lift the Control Panel assembly from the printer.

Step 5. Loosen the two screws holding the Control Panel to the metal frame.

Step 6. Lift the Control Panel from the metal frame.

The Control Panel Assembly can be adjusted so that it aligns snugly with the
top cover. To do this, loosen the screws and adjust the assembly until it fits
properly in the opening of the printer cover. Don't forget to tighten the
screws.

Summary of Contents for T6215





































































































































































Search results

Summary of Contents for T6215

Reviews:

Related manuals for T6215

Brands by name

Popular brands

Tally T6215, Maintenance Manual

Search results

Summary of Contents for T6215

Reviews:

Related manuals for T6215

Brands by name

Popular brands