157
Listening area:
Loudspeaker/earphone control:
1. Built-in Hi-Fi loudspeaker
When the microphones of all interpreter units in the
booth are disabled, you can listen to the
loudspeaker of the interpreter unit. Push the primary
knob to go to the floor channel. Turn the primary
knob to select a different channel.
2. Loudspeaker volume control knob
3. Earphone bass control knob
4. Earphone treble control knob
5. Earphone volume control knob
Input channel control:
6. Primary knob
Push the primary knob to go to the floor channel for
loudspeaker, turn the primary knob to select a
different channel;
When the monitor channel shortcut switch button (a
b c d e) was pressed, push the primary knob to go to
channel 1, turn the primary knob to select the input
channel;
When the output channel B/C switch button (B C)
was pressed, push the primary knob to go to
channel 1, turn the primary knob to select the output
channel.
7. Monitor channel shortcut switch button (a b c d e)
Switch to preset the input channel.
8. Floor channel ON/OFF switch
Press this button to access the floor language and
the “Floor” indicating light will be activated;
Switch between floor channel and auto-relay
channel.
Speaking area:
9. Microphone ON/OFF switch (Micro)
Press this button to turn on the microphone and the
red indicating light will be activated, press this button
again to turn off the microphone.
If the interpreter booth is off, the green indicating
light will be activated.
10. Output channel A/B/C switch with indicating
lights
Switch to preset the output channel.
11. Microphone mute key (Mute)
Push and hold the “Mute” button to temporarily
disable the microphone and the mute indicating
light will be activated. The speech timer does not
stop. Release this button on voice recovery.
12. Help key (HELP)
When connected to PC and controlled by
application software, press this key to ask the
operator for help and help information will be
displayed on the status bar of the application
software and the LCD of the operator unit.
13. Slow key (SLOW)
When the delegate is speaking too fast, press this
button (microphone of the interpreter unit must be
active) to remind him/her to slow down. If the
discussion unit is equipped with an LCD, the
message “Please speak slower!” will be displayed.
14. Intercom key (CB)
Press this key to ask the operator for intercom
function.
15. Intercom call key (CALL)
Press this key to ask the appointed CHAIR
(chairman, delegate or operator) for the intercom
function (For the correlative setup please refers to
section 2.4.5.).
16. Message key
（
)
When unread messages exist, this indicating light
will be activated, press this key to enter message
interface;
Push the a/b/c/d button to read the corresponding
message, the display shows the message;
Push the e button to cancel the message
interface.
17. Input channel audio playback key (REP.)
Push the REP. key to playback input channel
audio, the adjacent indicator lights up, playback
time is adjustable between 2 - 6 seconds (when
the microphone is on, push and hold the “Mute”
button and turn the primary knob to adjust the
repeat time);
Push the REP. key again to cancel playback.
21. BEEP key ( )
You can disable and enable the beeps of the
interpreter unit with the beeps key. When beeps
are enabled, the display shows a musical note.
The interpreter unit can generate beeps for
Summary of Contents for HCS-4100/50 Series
