SystemAir SysAer SR105 Regulation Manual Download Page 24

Page: 24 / 62

English

EXT

[°C]

STPCOMP

(10°C)

DIFFC (+10°C)

(0°C)

COMPM

(2°C)

EXT

[°C]

DIFFC

10°C

0°C

COMPM

19°C

21°C

Heating STP

EXT

[°C]

STPCOMP

(0°C)

DIFFC (-10°C)

(10°C)

COMPM

(2°C)

EXT

[°C]

DIFFC

10°C

0°C

COMPM

19°C

21°C

Heating STP

100%

Economizer

Air

Quality

(%)

AirQ_STP

AirQ_diff

22 SysAer

Compensation - Positive differential

Example with manual Heating setpoint = 21°C

Compensation - Negative differential

Example with manual Heating setpoint = 21°C

Winter Compensation
Winter set point compensation is enabled when the following conditions are encountered:
the unit is in winter mode

STPCOMP

Compensation set point [°C]

COMPM

Maximum compensation [°C]

DIFFC

Compensation differential [°C]

EXT

External temperature [°C]

4. ROOM AIR QUALITY CONTROL

Room air quality control opens the external damper to increase the percentage of fresh air when the room

air is too much polluted compared to the IAQ (Indoor Air Quality) sensor setpoint.
This function is available only with the IAQ sensor option, which is incompatible with the Indoor air humidity

sensor option. It requires the 2 or 3-damper options.

External damper is controlled by IAQ as illustrated in the figure below:

NB:
When this function asks for opening the external damper at the same time as freecooling for example, the

highest opening has the priority.

Summary of Contents for SysAer SR105































































Search results

Summary of Contents for SysAer SR105

Reviews:

Related manuals for SysAer SR105

Brands by name

Popular brands

SystemAir SysAer SR105, Regulation Manual

Search results

Summary of Contents for SysAer SR105

Reviews:

Related manuals for SysAer SR105

Brands by name

Popular brands