Symantec NetBackup 5230 Installation Manual Download Page 52

Page: 52 / 60

See “Installing and connecting an additional Symantec Storage Shelf to an
operational NetBackup 52xx appliance” on page 52.

■

Adding the new disk storage space to the system

This task makes the disk storage space of the new units available for use.

See “Adding the disk space of additional Symantec Storage Shelf units to an
operational NetBackup 52xx appliance from the NetBackup Appliance Web
Console” on page 54.

See “Adding the disk space of additional Symantec Storage Shelf units to an
operational NetBackup 52xx appliance from the NetBackup Appliance Shell
Menu” on page 56.

Note:

When you add an additional Symantec Storage Shelf to an operational

appliance, Symantec recommends that you schedule this task during low system
activity.

Installing and connecting an additional Symantec
Storage Shelf to an operational NetBackup 52xx
appliance

Use the following procedure to install and connect an additional Symantec Storage
Shelf to an operational NetBackup 52xx appliance.

Note:

When you add a storage shelf to an operational system, it is not necessary

to shut down the appliance server or any existing storage shelves.

To install and connect an additional Symantec Storage Shelf to an operational

NetBackup 52xx appliance

Install the new storage shelf units in the rack.

Locate the SAS cables that are shipped with each storage shelf and connect
them as described in the following diagram and text descriptions:

Adding storage shelves

Installing and connecting an additional Symantec Storage Shelf to an operational NetBackup 52xx appliance

Summary of Contents for NetBackup 5230





























































Search results

Summary of Contents for NetBackup 5230

Reviews:

Related manuals for NetBackup 5230

Brands by name

Popular brands

Symantec NetBackup 5230, Installation Manual

Search results

Summary of Contents for NetBackup 5230

Reviews:

Related manuals for NetBackup 5230

Brands by name

Popular brands