manualshive.com logo in svg

Sylvac D 100S, Instructions For Use Manual

Share
Download
Sylvac D 100S Instructions For Use Manual Download Page 46

46

= no display of class indicators.

= display class indicators.
= input of 3 classes, lower limit of class 1 is 1.21, upper limit of class 1 is 12.2, upper
   limit of class 2 is 12.3 and upper limit of class 3 is 12.4 (according to current unit).

= output of memorized class values.

= displays a 20 characters max message on the first line of the D100S display. The
   end of message is given is given by CR (Carriage Return). This message is cleared by
   pressing any key on D100S unit or by sending the NOR remote command.

= allocates data transmission function to external contact (foot pedal).
   (

refer to section 1.6.11

).

= display hold or store.
= reset Min/Max registers.
= preset display.
= change channel.
= D110 command.
= start scanning.
= status transmitted automatically.
= status transmitted on request.
= transmission of display hold or store.
= new Min/Max the transmission of values.
= preset then transmission of values.
= transmission of change channel.
= D110 command then transmission of values.
= start scanning then transmission of values.
= D110 command then start scanning and transmission of values.
= D110 command then start scanning.
= new Min/Max then store or hold.
= preset then store or hold.
= store + change channel.
= D110 command then store or hold.
= start scanning the store.
= D110 command then start scanning then store.
= start scanning then transmission of values then store/hold.
= new Min/Max (if necessary) then store/hold and change channel.

= new Min/Max then Print + change channel.
= new Min/Max then change channel.
= print + store + change channel.
= D110 command then print and store.
= preset then scanning.
= D110 command then scanning then print + store/hold.
= request status of external contact (corresponding to EXT 8)
   the unit transmits 0 (zero) if no external contact.
   The unit transmits 1 if an external contact has occurred (status is automatically reset
   To 0).
= actives the function of the external contact 1
= actives the function of the external contact 2 (

refer to section 1.6.11

).

= identification of instrument—> the unit responds «SYLVAC D100S date V1.4»
   V1.4 = firmware version

CLA 0

(CLASSIFICATION)

CLA 1
CLA 3 12.1 12.2 12.3 12.4

CLA?

DIS ……...

(DISPLAY)

EXT 0

(EXTERNAL CONTACT)

EXT 1
EXT 2
EXT 3
EXT 4
EXT 5
EXT 6
EXT 7
EXT 8
EXT 9
EXT 10
EXT 11
EXT 12
EXT 13
EXT 14
EXT 15
EXT 16
EXT 17
EXT 18
EXT 19
EXT 20
EXT 21
EXT 22
EXT 23
EXT 24

EXT 25
EXT 26
EXT 27
EXT 28
EXT 29
EXT 30
EXT?

FS1
FS2

IDE

 ou 

ID?

(IDENTIFICATION)

Summary of Contents for D 100S













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands