manualshive.com logo in svg

Sylvac D 100S, Instructions For Use Manual

Share
Download
Sylvac D 100S Instructions For Use Manual Download Page 35

35

13/ Enter nominal size and tolerances for all channels to be scanned (refer to section 1.6.7).

14/ Put a block gauge (master) under the probes and be ready to calibrate the channels.

15/ Enter the preset values according to the master for all required channels. For a new calibration in scanning
      mode, just press 

Preset

 when the master is in place.

16/ The system is now ready. Position the work piece to be measured and when the probes are in the measuring
position, press the 

Scan

 key.

According to the particular channel allocation specified in point 10, scanning will stop at channel 4 and the following
will be displayed :

                                                             Take a minimum measurement on channel 4 and then press 

Enter

 key or

                                                             foot pedal.

                                                             In case of a wrong measurement, the 

Clear

 key will allow a new

                                                             measurement to be taken.

17/ When scanning is completed, the following will be displayed (numerical value are given as examples) :

                                                             Sequential work-pieces numbered : from 1 to max 65 000.
                                                             General indication for the measured work piece from indicators lights.
                                                             This criteria takes into account the internal or external measurement for
                                                             each channel. (

refer to tolerances in section 1.6.7

)

                                                             Display of channel number, measuring mode if channel is in A +/- B mode,
                                                             And measured value or, if tolerances are active, of the difference between
                                                             nominal size and measured value and graphical display <, = or >.

The following keys are active in Scan mode :

                        Starts a new scan. Work piece numbering is done automatically (from 1 to n pieces). For 40 or 80
                        Columns printing format, it is also possible to enter an alpha-numerical identification of each scanned
une                  work piece (

refer to section. 1.6.14 

: 

Print 

key).

                        Displays or removes the tolerance indicators for each channel.
                        

Tol not activated 

: measured value is displayed.

                        

Tol activated 

: difference between nominal and measured value is displayed, followed by 

E

 for an

                        external measurement or 

I

 for an internal  measurement, and finally by tolerance indicators 

<

,

=

 or 

>

.

                        The first displayed values show a maximum of 5 channels. Any following channels will be shown by
                        Pressing this key. When the last table is reached ( the arrow      disappears from the upper-right-hand
                        Side of the display), you can exit scanning mode by pressing this key again.

                        This key allows display of the preceding table. When the first table is reached ( the arrow
                        disappears) pressing the key again allows you to exit scanning mode.

Summary of Contents for D 100S













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands