manualshive.com logo in svg

Sylvac D 100S, Instructions For Use Manual

Share
Download
Sylvac D 100S Instructions For Use Manual Download Page 19

19

3/ Confirm input number with 

Enter 

key.

Following display will appear :

                        

The channel selected by default in 3/ will appear. A number from 1 to 64 can

                                                               be entered.

4/ confirm input number with 

Enter 

key.

Following display will appear :

                                      press 1 for analog probes.

                                                   press 2 for Opto-RS instruments used with simplex cable (no adapter

                                                                required)

                                                   press 3 for Opto-RS instruments used with duplex cable (no adapter

RS duplex (pas                                       required).

                                                   The value of the RS232 instrument (indicator, caliper , Microcal…will be

                                                                displayed continuously on the D100S. The calculation functions or the unit
                                                                are available : TOL, CLASS, PRESET, STORE, STAT….

                                                                Using one or more D104 units, 48 RS232 channels can be connected to
                                                                D100S unit.

5/ The first display will then appear and a new allocation can be started, or exit with 

Clear 

key.

Example : using one D102 and 2 P10 probes for internal bore measurements. The first probe measures 3 kinds of
bores with corresponding presets and classifications, and the second measures 4 types of bore with corresponding
presets and tolerances. An independent measurement is required on the last channel with a Microcal micrometer
used with a simplex cable.

Channels  1,2 and 3 are thus allocated to probe n° 1    :     1 —> 1            2 —> 1           3 —> 1

Channels  4,5,6 and 7 are allocated to probe n°2          :     4 —> 2            5 —> 2           6 —> 2           7 —> 2

Channel 8 is allocated to input 8 of the RS232 simplex :     8 —> 8 RS

Summary of Contents for D 100S













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands