manualshive.com logo in svg

Sylvac D 100S, Instructions For Use Manual

Share
Download
Sylvac D 100S Instructions For Use Manual Download Page 34

34

1.6.13 SCAN KEY

Starts scanning of 1 to n channels (n being defined as indicated below), compares each measurement with its
assigned tolerance and displays the results with a global indication : part OK (green light), rework (yellow light), or
reject (red light). This information is also transmitted to the opto-coupler (refer to section 1.8.3).

It is also possible to configure the external contact (foot pedal) for scanning.

Scanning mode requires the connection of one or more multi-channel units 

D102

 or 

D108

 (for probes) or 

D104

 (for

RS232 instruments (refer to sections 2.3 and 3.3).

How to use the scanning mode :

1/ connect the 

D100S

 unit with one or more 

D102/108/D104

. If required, connect a foot pedal or another external

contact to start scanning. A pneumatic unit D110 or D110V vacuum can also be used for lifting the probes.

2/ Press 

Setup

 key  3/ then 

Scan

 key

4/ Enter the number of the first channel to be scanned (1 to 63).

5/ Enter the number of the last channel to be scanned (1 to 64).

6/ If necessary, enter the channel number on which to stop (e.g. opportunity to move the workpiece). Pressing  Enter
    or foot pedal (whatever its function) will continue the scanning. If no stop is required, just press ENTER (stop
    channel = last channel).

7/ If required, assign the function of the external to start the scanning, combined as required with data transmission
    or store and/or with probe lifting, then enter delay time between external contact and start scanning (explained
    with Set Up function in section 1.6.11)

8/ If the data is to be stored, the number of channels to be stored must be entered in 

Setup

 – 

Store

 then 5 (

refer to

    section 1.6.15

).

9/ If required, enter Min/Max mode for any channels. Scanning automatically stops when a given channel is in
    Min/Max mode and waits for measurement. To continue scanning, simply press the 

Enter

 key or 

foot pedal

.

10/ Enter the channels working in the A +/- B or A+/- function (do not forget the correct direction sign) the diameter
or any  multiplication factor function, allocation of a probe to several channels (

refer to section 1.6.3

)

      Example :       channel 1 - 6
                             channel 2 - 7
                             channel 3 + 8
                             channel 4 minimum measurement
                             channel 5 diameter measurement

5 channels have to be scanned, of which 3 in A +/- B.

11/Choose the resolution of the display. The lower the resolution, the faster the scanning will be :
      using 0.0001 mm / 0.00001 in : 

approx. 2 measurements / sec.

      using 0.001 mm / 0.0001 in :            approx. 4 measurements / sec.
      using 0.01 mm / 0.001 in :                approx. 5 measurements / sec.
      using 0.1 mm / 0.01 in :                    approx. 6 measurements / sec.

12/ Select scanning start channel ( in order to start all preset and tolerance inputs from this channel).

Summary of Contents for D 100S













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands