manualshive.com logo in svg

Sylvac D 100S, Instructions For Use Manual

Share
Download
Sylvac D 100S Instructions For Use Manual Download Page 4

4

1.6.15 STORE KEY

...................................................................................................................................................50

1.7  CALIBRATION OF THE UNIT

..............................................................................................................................52

1.7.1 General calibration

...........................................................................................................................................52

1.7.2 Coupling probe to unit

......................................................................................................................................52

1.8  REAR PANEL

.......................................................................................................................................................54

1.8.1  RS-232-C Input/output

....................................................................................................................................54

1.8.2  RS-232-C input instrument (Opto-RS simplex or duplex)

...............................................................................54

1.8.3  Outputs

............................................................................................................................................................55

1.8.4  Centronics Output : parallel printer link

...........................................................................................................56

1.8.5  Socket for mains charger

................................................................................................................................57

1.8.6  Socket for external contact 1, e.g. foot pedal

..................................................................................................57

1.8.7  Socket for external contact 2, e.g. second pedal

............................................................................................57

1.8.8  Probe input

......................................................................................................................................................57

1.8.9  Command output

.............................................................................................................................................57

1.9   IN CASE OF DIFFICULTY

...................................................................................................................................58

1.9.1 No display on screen when unit is switched on.

..............................................................................................58

1.9.2 Complete reset of unit.

.....................................................................................................................................58

1.9.3 Loss of memory content.

..................................................................................................................................58

1.9.4 Software version

..............................................................................................................................................59

1.9.5 Special symbols

...............................................................................................................................................59

1.10 REPLACING THE LITHIUM MODULE

................................................................................................................60

1.11 REPLACING ACCUMULATORS

.........................................................................................................................61

1.12 TECHNICAL SPECIFICATIONS

..........................................................................................................................62

1.13 DELIVERY

............................................................................................................................................................63

1.14  ACCESSORIES

...................................................................................................................................................64

2. MULTICHANNEL UNITS : «  CHANNELS (D102) ET

     8 CHANNELS(D108)

.........................................................................65

2.1  GENERAL DESCRIPTION

....................................................................................................................................65

2.2  REAR PANEL (D108 unit)

....................................................................................................................................65

2.3  OPERATION

..........................................................................................................................................................65

2.4  TECHNICAL SPECIFICATIONS OF D102 AND D108 UNITS

.............................................................................66

2.5  ACCESSORIES

.....................................................................................................................................................66

3 D104 4-CHANNEL RS232 SWITCHING UNIT

...................................67

3.1  GENERAL  DESCRIPTION

...................................................................................................................................67

3.2 CONNECTION OF 2 D104 UNITS AND 1 D108 UNIT ON D100S UNIT

..............................................................67

3.3  OPERATION

..........................................................................................................................................................67

3.4  TECHNICAL SPECIFICATIONS

...........................................................................................................................68

3.5 ACCESSOIRES

......................................................................................................................................................68

Summary of Contents for D 100S













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands