Supero FatTwin F627R2-F73 User Manual Download Page 141

Page: 141 / 144

B-1

Appendix B: System Specifi cations

Appendix B

System Specifi cations

Note:

Unless noted specifi cations apply to a complete system (all serverboards).

There are four motherboard drawer nodes per system.

Processors

Two E5-2600 series series processors per node in Socket R LGA 2011 type

sockets

Note:

please refer to our website for details on supported processors.

Chipset

One C602J chipset per node

BIOS

128 Mb AMI BIOS® Flash EEPROM per node

Memory Capacity

The X9DRFF-7 serverboard has eight (8) DIMM slots supporting up

to 256 GB of RDIMM/LDIMM registered ECC or 64 GB of UDIMM

DDR3-1600/1333/1066/800 MHz speed SDRAM in up to 1 GB, 2 GB, 4 GB,

8 GB, 16 GB or 32 GB sizes at 1.35V or 1.5V voltages per node.

Note:

refer to Section 5-5 for details on installation.

Note:

Check the Supermicro website (

www.supermicro.com

) for the latest memory support

information.

SAS/SATA Drive Bays

Each node of the FatTwin F627R2-F73 contains eight (8) hot-swap drive bays to

house standard 2.5" SAS/SATA drives

PCI Expansion

The FatTwin F627R2-F73 has 1x PCI-E 3.0 x16 low-profi le slot available per

node.

Summary of Contents for FatTwin F627R2-F73

















































































































































Search results

Summary of Contents for FatTwin F627R2-F73

Reviews:

Related manuals for FatTwin F627R2-F73

Brands by name

Popular brands

Supero FatTwin F627R2-F73, User Manual

Search results

Summary of Contents for FatTwin F627R2-F73

Reviews:

Related manuals for FatTwin F627R2-F73

Brands by name

Popular brands