Supero FatTwin F627R2-F73 User Manual Download Page 128

Page: 128 / 144

7-24

FatTwin F627R2-F73 FatTwin

This item displays the status of TPM Support to indicate if TPM is currently

active or deactivated.

TPM Owner Status

This item displays the status of TPM Ownership.



Intel TXT (LT-SX) Confi guration

Intel TXT (LT-SX) Hardware Support

This feature indicates if the following hardware components support the Intel

Trusted Execution Technology.

CPU

TXT (Trusted Execution Technology) Feature

Chipset

TXT (Trusted Execution Technology) Feature

Intel TXT (LT-SX) Confi guration

This feature displays the following TXT confi guration setting.

TXT (LT-SX) Support

This item indicates if the Intel TXT support is enabled or disabled. The default

setting is

Disabled

Note

: Be sure to format your TPM module before enabling TXT (LT-SX)

support for this feature to work properly.

Intel TXT (LT-SX) Dependencies

For Trusted Execution Technology to work properly in the system, be sure to

enable the features displayed below.

VT-d Support

Intel Virtualization Technology with Direct I/O support

VT Support

Intel Virtualization Technology support

Summary of Contents for FatTwin F627R2-F73

















































































































































Search results

Summary of Contents for FatTwin F627R2-F73

Reviews:

Related manuals for FatTwin F627R2-F73

Brands by name

Popular brands

Supero FatTwin F627R2-F73, User Manual

Search results

Summary of Contents for FatTwin F627R2-F73

Reviews:

Related manuals for FatTwin F627R2-F73

Brands by name

Popular brands