Supero FatTwin F627R2-F73 User Manual Download Page 88

Page: 88 / 144

6-4

FatTwin F627R2-F73 USER'S MANUAL

6-4 Installing and Removing Hard Drives

The F424BD chassis contains four individual motherboards in four separate 2U

nodes. Each motherboard node controls the hard drives contained within that

node. Note that if a motherboard node is pulled out of the chassis, the hard drives

associated with that node will power down as well. Refer to the chart below for the

chassis confi guration. hot-swappable hard drives can be removed from the chassis

without powering down the server or removing the node from the chassis.

Only enterprise level hard drives are recommended for use in Supermicro chassis.

F424BD Node Locations in the Chassis

Node 2

Controls eight 2.5" HDDs, B1-B8

Node 4

Controls eight 2.5" HDDs, D1-D8

Node 1

Controls eight 2.5" HDDs, A1-A8

Node 3

Controls eight 2.5" HDDs, C1-C8

Figure 6-2: Hard Drives and the Corresponding Motherboards

Node 2

Node 4

Node 1

Node 3

Summary of Contents for FatTwin F627R2-F73

















































































































































Search results

Summary of Contents for FatTwin F627R2-F73

Reviews:

Related manuals for FatTwin F627R2-F73

Brands by name

Popular brands

Supero FatTwin F627R2-F73, User Manual

Search results

Summary of Contents for FatTwin F627R2-F73

Reviews:

Related manuals for FatTwin F627R2-F73

Brands by name

Popular brands