Supero FatTwin F627R2-F73 User Manual Download Page 108

Page: 108 / 144

7-4

FatTwin F627R2-F73 FatTwin

This displays the amount of memory that is available in the system.

7-3 Advanced Setup Confi gurations

Use the arrow keys to select Advanced Setup and press <Enter> to access the

following submenu items.



Boot Feature

Quiet Boot

This feature allows the user to select bootup screen display between POST

messages and the OEM logo. Select Disabled to display the POST messages.

Select Enabled to display the OEM logo instead of the normal POST messages.

The options are

Enabled

and Disabled.

AddOn ROM Display Mode

Use this item to set the display mode for the Option ROM. Select Keep Current to

use the current AddOn ROM Display setting. Select Force BIOS to use the Option

ROM display mode set by the system BIOS. The options are

Force BIOS

and

Keep Current.

Bootup Num-Lock

Summary of Contents for FatTwin F627R2-F73

















































































































































Search results

Summary of Contents for FatTwin F627R2-F73

Reviews:

Related manuals for FatTwin F627R2-F73

Brands by name

Popular brands

Supero FatTwin F627R2-F73, User Manual

Search results

Summary of Contents for FatTwin F627R2-F73

Reviews:

Related manuals for FatTwin F627R2-F73

Brands by name

Popular brands