manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 57

www.stryker.com

6086-009-001 REV B

57

Return To Table of Contents

Cleaning

In general, when used in those concentrations recommended by the manufacturer, either phenolic type or quaternary 
(

excluding Virex

®

 TB

) type disinfectants can be used.  Iodophor type disinfectants are not recommended for use 

because staining may result.  

Suggested cleaners for the cot surfaces and restraint straps:

• 

Quaternary Cleaners (active ingredient - ammonium chloride)

• 

Phenolic Cleaners (active ingredient - o-phenylphenol)

• 

Chlorinated Bleach Solution (5.25% - less than 1 part bleach to 100 parts water)

Note: 

 Do not immerse the restraint strap metal buckle components in water.  Rinse with clean water.  Allow to air dry.

Avoid over saturation and ensure that the product does not stay wet longer than the chemical manufacturer’s guidelines 
for proper disinfecting.

 WARNING

SOME CLEANING PRODUCTS ARE CORROSIVE IN NATURE AND MAY CAUSE DAMAGE TO THE PRODUCT IF USED 
IMPROPERLY.  If the products described above are used to clean Stryker EMS equipment, measures must be taken 
to ensure the cots are wiped with clean water and thoroughly dried following cleaning.  Failure to properly rinse and 
dry the cots will leave a corrosive residue on the surface of the cots, possibly causing premature corrosion of critical 
components. 

Note:  

Failure to follow the above directions when using these types of cleaners may void this product’s warranty (see 

page 155

).

REMOVAL OF IODINE COMPOUNDS

Use a solution of 1/2 Tablespoon Sodium Thiosulfate in a pint of warm water to clean the stained area. Clean as soon 
as possible after staining occurs. If stains are not immediately removed, allow solution to soak or stand on the surface. 
Rinse surfaces which have been exposed to the solution in clear water before returning unit to service.

 WARNING

Failure to properly clean or dispose of contaminated mattress or cot components will increase the risk of exposure to 
bloodborne pathogens and may cause injury to the patient or the operator.

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands