manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 28

28

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

Cot Operation

ADJUSTING THE HEIGHT OF AN EMPTY COT WITH ONE OPERATOR

To raise or lower the cot from the foot end: 

1.  Standing at the foot end of the cot, grasp the lower foot end lift tube. 
2.  Tip the cot up onto the load wheels (see Figure 14). 
3.  Squeeze and hold the release handle and raise or lower the foot end to the desired position.  The handle is 

released when the desired position is reached. 

4.  Lower the cot back onto the four base wheels (see Figure 15). 

To raise or lower the cot from the side: 

1.  Place one foot on the outer base tube. 
2.  Grasp the side release handle with one hand. Place your other hand on the outer support rail to help stabilize the 

cot (see Figure 16). 

3.  Squeeze the side release handle and raise or lower the cot to the desired position.  The handle is released when 

the desired position is reached (see Figure 17).

 WARNING

If lowering the cot to the lowest position (position 1), remove your foot from the base tube or injury could result.

Figure 14:  Cot Tipped on Load Wheels

Figure 15:  Cot Lowered to Ground

Figure 16:  Holding Outer Support Rail

Figure 17:  Lowering Cot from Side

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands