manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 46

46

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

Optional Accessories

USING THE EQUIPMENT HOOK

Use the equipment hook (A) (see Figure 46) to hang additional accessories or equipment, such as defibrillators or 
monitors.

 CAUTION

To avoid damage to the equipment 
hook, the weight of the accessories 
or equipment must not exceed 35 lb 
(15.9 kg).

Figure 46:  Equipment Hook 

A

USING THE HEAD EXTENSION WITH PILLOW

You can install the head extension assembly over the fowler to provide head end support.  

Attach the pillow to the head extension by placing the support into the flap on the bottom of the pillow.  Secure the 
pillow to the Velcro

®

 on the bottom of the support.

Note:  

The head extension with pillow (p/n 6100-044-000) is not compatible with the optional equipment hook (p/n 

6500-147-000) or optional fowler oxygen bottle holder (p/n 6500-141-000).

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands