manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 39

www.stryker.com

6086-009-001 REV B

39

Return To Table of Contents

OPERATING THE OPTIONAL WHEEL LOCKS

To activate the optional wheel locks

, press fully down on the pedal (A) as shown in Figure 36 until it stops and is 

resting firmly against the surface of the wheel.

To release the optional wheel locks

, depress the upper face of the pedal with your foot or lift up with your toe under 

the pedal. The upper portion of the pedal will rest against the caster frame when the wheel lock is released.

 WARNING

• 

Never apply the optional wheel locks while a patient is on the cot. Tipping could occur if the cot is moved while a 
wheel lock is applied, resulting in injury to the patient or operator and/or damage to the cot.

• 

Never leave a patient unattended on the cot or injury could result. Hold the cot securely while a patient is on the 
cot.

• 

Never install or use wheel locks on a cot with excessively worn wheels. Installing or using wheel locks on wheels 
with less than a 6” diameter could compromise the holding ability of the wheel lock, resulting in injury to the patient 
or operator and/or damage to the cot or other equipment.

 CAUTION

Wheel locks are only intended to help prevent the cot from rolling while unattended and to aid in patient transfer. A wheel 
lock may not provide sufficient resistance on all surfaces or under loads.

Operation Guide

Figure 36:  Wheel Lock

A

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands