manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 27

www.stryker.com

6086-009-001 REV B

27

Return To Table of Contents

Operation Guide

ADJUSTING THE HEIGHT OF THE COT WITH TWO OPERATORS

 WARNING

• 

Grasping the cot improperly can cause injury. Keep hands, fingers and feet away from moving parts. To avoid in-
jury, use extreme caution when placing your hands and feet near the base tubes while raising and lowering the cot.

• 

Ensure proper hand placement on hand grips. Hands should be clear of red safety bar pivots while loading and 
unloading the cot or whenever changing height position of the cot with two or more operators.

• 

When operating the side release handle, keep hands away from the foot end release handle to avoid injury.

You can raise or lower an unoccupied cot with one operator.  If a patient is on the cot, a minimum of 

two (2) trained 

operators

 (one located at each end of the cot) are required to raise or lower the of the cot.

To raise or lower the cot from the ends:

1.  The operator at the foot end of the cot squeezes the release handle (A or B) while a secure grip is maintained on 

the lifting bars (see Figure 13).  

2.  Both operators must lift the cot until the weight is off the latching mechanism (approximately 1/4”).  
3.  The operator at the foot end squeezes and holds the release handle and both operators then raise or lower the cot 

together.  The handle is released when the desired position is reached.  Both operators should maintain a secure 
grip on the litter frame until the latching mechanism is securely locked into position. 

To raise or lower the cot from the sides:

1.  Check the cot to determine if the 

side release handle is on the patient 
left or right side.

2.  The operator on the patient’s right 

or left (depending on the location 
of the release handle) reaches the 
release handle at the midpoint of 
the litter (C).  Both operators must 
lift the cot until the weight is off the 
latching mechanism (approximately 
1/4”) (see Figure 13).  

3.  The operator at the patient’s right or 

left (depending on the location of the 
release handle) squeezes and holds 
the release handle.  Both operators 
then raise or lower the cot together.  
The handle is released when the 
desired position is reached.  Both 
operators should maintain a secure 
grip on the litter frame until the 
latching mechanism is securely 
locked into position. 

Figure 13:  Adjusting the Cot Height

A

C

B

D

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands