manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 72

72

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

INNER, OUTER TUBE REPLACEMENT

Tools Required:

 

• 

(2) Saw Horse

• 

3/8” Combination Wrench 

• 

7/16” Combination Wrench

• 

T25 Torx Driver 

• 

(2) 9/16” Combination Wrench 

• 

Dead Blow Hammer

• 

3/16” Allen Wrench

Procedure:

1.  Complete steps 1-7 from “Inner, Inner Tube Replacement” on 

page 69

.

2.  Remove the inner tube.
3.  Using a T25 Torx driver, remove the screw that secures the base dead stop from the outer tube.
4.  Using a 7/16” combination wrench and a 3/16” Allen wrench, remove the two screws that secure the cap bearings 

to the base litter interface bracket (one on each side).

5.  Squeeze the head release handles and slowly remove the head section assembly.
6.  Using a 7/16” combination wrench and 3/16” Allen wrench, remove the bolt that secures the litter interface bracket.
7.  Using a 3/16” Allen wrench, remove the two screws that hold the litter interface bracket together.
8.  For the trend option, using a T25 driver, remove the two screws that secure the trend support bracket.
9.  For the gatch option, using a T25 driver, remove the four screws that secure the gatch support brackets.
10.  Pull outward on the outer rail until the litter interface bracket is off of the litter crosstube.
11.  Remove the outer tube from the litter crosstube and save the tube bushings to reuse on the new tube.
12.  Reverse the above procedures to install the new outer tube.

Note: 

Make sure that the X-frame guard screw hole on the new inner tube is facing the top of the cot when 

reassembling.

13.  Verify proper operation of the unit before returning it to service.

Service Information

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands