manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 23

www.stryker.com

6086-009-001 REV B

23

Return To Table of Contents

Adjusting Cot Load Height

Before placing the cot into service, confirm that the cot load height is set correctly for your vehicle.  The cot load height 
can be adjusted to match the height of the vehicle deck.  If the cot does not line up correctly, adjustments may need 
to be made to the cot load height.

 WARNING

Before placing the cot into service, confirm that the cot load height is set correctly for your vehicle.

To check the load height of the 

Performance-PRO™ XT

 cot:

1.  Roll the cot up to the loading area of your vehicle.
2.  Compare the difference between the deck height of the 

vehicle and the load height of the cot.

3.  Select HIGH, MID or LOW depending on the cot load 

height requirements (see Figure 12).  For example:

• 

The HIGH marking on the rack is recommended for 
vehicle deck heights above 32 inches.

• 

The MID marking on the rack is recommended for 
vehicle deck heights between 30 and 32 inches.

• 

The LOW marking on the rack is recommended for 
vehicle deck heights below 30 inches.

4.  Verify that the safety hook always engages the cot safety 

bar, regardless of how the cot is unloaded from the 
vehicle.  If the safety bar misses the safety hook, select 
the next lower height setting.

For deck heights above 32”

For deck heights between 30-32”

For deck heights below 30”

Figure 12:  Cot Load Height

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands