Stryker 6086 Operation & Maintenance Manual Download Page 69

Page: 69 / 158

www.stryker.com

6086-009-001 REV B

Return To Table of Contents

Service Information

Figure 68

INNER, INNER TUBE REPLACEMENT

Tools Required:

•

(2) Saw Horse

•

3/8” Combination Wrench

•

7/16” Combination Wrench

•

T25 Torx Driver

•

(2) 9/16” Combination Wrench

•

Dead Blow Hammer

Procedure:

1. Using a T25 Torx driver, remove the four

button head cap screws (A) from the
base stiffener (B) (Figure 68).

2. Lower the cot to the full down position.
3. Using two saw horses, flip the cot upside

down on the saw horses to support the
cot.

4. Using a 3/8” and 7/16” combination

wrench, remove all four caster mount
bolts (C) that secure the outer lift tube
assemblies to the foot base tubes

(Figure 69).

5. Using two 9/16” combination

wrenches and a dead blow hammer,
remove the base connecting rod
(D) and centerlock hex jam nut (E).

Note:

Save the bearings (F) that fall

out. (Figure 71).

6. Remove the outer base tube weldment

(G) on the side that is damaged. Leave
the opposite side on to support the
X-frame (Figure 70).

7. Slide the foot base tubes (H)

through the X-frame legs to
loosen the X-frame (Figure 70).

Note:

The opposite side will still have

the outer base tube and foot base tubes
attached to the X-frame.

8. Remove the inner tube and save the

bushings (J) to reuse on the new tube.

9. Reverse the above procedures to install

the new inner tube.

10. Verify proper operation of the unit before

returning it to service.

Figure 70

Figure 71

Figure 69

Summary of Contents for 6086































































































































































Search results

Summary of Contents for 6086

Reviews:

Brands by name

Popular brands

Stryker 6086, Operation & Maintenance Manual

Search results

Summary of Contents for 6086

Reviews:

Brands by name

Popular brands