manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 103

Return To Table of Contents

www.stryker.com

6086-009-001 REV A

103

Foot End Assembly, Left

Foot End Assembly, Left - 6085-001-015 Rev B (Reference Only)

Item 

Part No. 

Part Name 

Qty. 

A 

0004-376-000 

Button Head Cap Screw 

2 

B 

0004-614-000 

Button Head Cap Screw 

8 

C 

0004-615-000 

Button Head Cap Screw 

6 

D 

0007-086-000 

Truss Head Screw 

2 

E 

0008-033-000 

Socket Head Shoulder Screw 

1 

F 

0016-028-000 

Fiberlock Hex Nut 

3 

G 

0016-131-000 

Nylock Hex Nut 

14 

H 

0023-167-000 

Delta Screw 

2 

J 

0025-079-000 

Dome Head Rivet 

8 

K 

6080-040-044 

Link Release Spacer 

2 

L 

6082-040-025 

End Link Bushing 

2 

M 

6082-040-061 

Release Handle Assembly  

1 

N 

6085-001-106 

Upper Lift Bar 

1 

P 

6085-001-107 

Lower Lift Bar 

1 

R 

6085-001-108 

Rear Plate Lift Support Tube 

1 

T 

6085-001-109 

Face Plate Lift Support Tube 

1 

U 

6085-001-111 

Pull Handle Link 

1 

V 

6500-001-133 

Machined Extruded Bracket 

2 

W 

6500-001-144 

Transition Cap 

2 

Y 

6500-001-154 

Outside Pull Handle 

2

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands