manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 17

www.stryker.com

6086-009-001 REV B

17

Return To Table of Contents

Note: 

The Cot Fastener Installation instructions on 

page 17

 through 

page 22 

are intended for cots that you will 

NOT use with Power-LOAD.  For Model 6086 cots with the Power-LOAD option, see the Power-LOAD Operations/
Maintenance Manual for installation instructions.

The Stryker Cot Fastener Systems are designed to be compatible only with cots which conform to the installation 
specifications listed on 

page 18

.

 WARNING

It is the responsibility of the cot operator to ensure that the cot being used in the Stryker Cot Fastener Systems meets the 
installation specifications listed on 

page 18

.  Injury may result if a non-compatible cot is used in the Stryker Fastener 

System.

Note: 

 

Adjustment of the rail clamp assembly may be required in order to compensate for any variation in the cot 

retaining post position depending on the cot manufacturer and model number.   

For more information about the Stryker Cot Fastener Systems, see the Cot Fastener Operations/Maintenance Manual.

Cot Fastener Installation

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands