manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 155

www.stryker.com

6086-009-001 REV B

155

Return To Table of Contents

Warranty

Stryker EMS

, a division of the Stryker Corporation, offers two distinct warranty options in the United States:

One (1) year parts and labor

. Under this option, Stryker EMS warrants to the original purchaser that its products should 

be free from manufacturing non-conformances that affect product performance and customer satisfaction for a period of 
one (1) year after date of delivery. Stryker’s obligation under this warranty is expressly limited to supplying replacement 
parts and labor for, or replacing, at its option, any product that is, in the sole discretion of Stryker, found to be defective. 
 

Two (2) year parts.

 Under this option, Stryker EMS warrants to the original purchaser that non-expendable components 

of its products should be free from manufacturing non-conformances that affect product performance and customer 
satisfaction for a period of two (2) years after date of delivery. Stryker’s obligation under this warranty is expressly 
limited to supplying replacement parts for, or replacing, at its option, any product which is, in the sole discretion of 
Stryker, found to be defective. Expendable components, i.e. mattresses, restraints, I.V. poles, storage nets, storage 
pouches, oxygen straps, and other soft goods, have a one (1) year limited warranty with this option.

Under either warranty option, the Stryker 

Performance-PRO™ XT

 is designed for a 7 year expected service life under 

normal use, conditions, and with appropriate periodic maintenance as described in the maintenance manual.  Stryker 
warrants to the original purchaser that the welds on the 

Performance-PRO™ XT

 will be free from structural defects 

for the expected 7 year life of the product as long as the original purchaser owns the product.  Original purchasers will 
also obtain a three (3) year limited parts warranty for the X-frame components.

Upon Stryker’s request, purchaser shall return to Stryker’s factory any product or part (freight prepaid by Stryker) for 
which an original purchaser makes a warranty claim.

Any improper use or alteration or repair by unauthorized service providers in such a manner as in Stryker’s judgment 
affects the product materially and adversely, shall void this warranty. Any repair of Stryker products using parts not 
provided or authorized by Stryker shall void this warranty. No employee or representative of Stryker is authorized to 
change this warranty in any way.

This statement constitutes Stryker EMS’s entire warranty with respect to the aforesaid equipment. STRYKER MAKES 
NO OTHER WARRANTY OR REPRESENTATION EITHER EXPRESSED OR IMPLIED, EXCEPT AS SET FORTH 
HEREIN. THERE IS NO WARRANTY OF MERCHANTABILITY AND THERE ARE NO WARRANTIES OF FITNESS 
FOR ANY PARTICULAR PURPOSE. IN NO EVENT SHALL STRYKER BE LIABLE HEREUNDER FOR INCIDENTAL OR 
CONSEQUENTIAL DAMAGES ARISING FROM OR IN ANY MANNER RELATED TO SALES OR USE OF ANY SUCH 
EQUIPMENT.

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands