background image

11

Assembly bottom support on 

concrete block

First install the base console in accordance with the requirements to 

the dimensions of bottom support.

1420014 bottom support 20°/30° 200 V

1420024 bottom support 45°/60° 200 V

1420018 bottom support 20°/30° 240 V

1420022 bottom support 45°/60° 240 V

1420060 bottom support 20°       270 V

1420061 bottom support 30°       270 V

1420062 bottom support 45°       270 V

1420063 bottom support 60°       270 V

1420011 bottom support 20°/30° 200/240/270 H

1420020 bottom support 45°/60° 200/240/270 H

Next place the concrete block. Pay attention to the exact 

observance of the specified clearances between the concrete 

blocks. The short distance between the threaded sleeve and block 

edge (10 cm) shows the front of the block. Make sure that every 

concrete block is on the same mounting position and aligned in a 

row (e.g. by a line mark).

1420100 concrete block 65 kg 

Now remove from all concrete blocks, the protective caps for the 

integrated threaded sleeves.

 

Then place the base consoles on the concrete blocks and secure 

them with the screws M10. All other consoles have to be oriented 

exactly in a row (e.g. by a line mark).

 
1420003 Fastening set for bottom support

  

Now weight down the concrete block with the additional block. 

Prepare for installing the collectors all consoles as above described.

1420101 additional block 45 kg

Summary of Contents for FKA 200H









































Reviews: