STG global TANVAC HDV3000 Operator'S Manual Download

Page: 66 / 329

Operation Section
Lifting and Storage

i04342729

Product Lifting

SMCS Code:

1000; 1404; 7002

Illustration 32

g00103219

NOTICE

Never bend the eyebolts and the brackets. Only load

the eyebolts and the brackets under tension. Re-

member that the capacity of an eyebolt is less as the

angle between the supporting members and the ob-

ject becomes less than 90 degrees.
When it is necessary to remove a component at an

angle, only use a link bracket that is properly rated for

the weight.
Use a hoist to remove heavy components. Use an

adjustable lifting beam to lift the engine. All

supporting members (chains and cables) should be

parallel to each other. The chains and cables should

be perpendicular to the top of the object that is being

lifted.
Some removals require lifting the fixtures in order to

obtain proper balance and safety.
To remove the engine only, use the lifting eyes that

are on the engine.
Lifting eyes are designed and installed for the

specific engine arrangement. Alterations to the lifting

eyes and/or the engine make the lifting eyes and the

lifting fixtures obsolete. If alterations are made,

ensure that proper lifting devices are provided.

Consult your Cat dealer for information regarding

fixtures for proper engine lifting.

i05111635

Product Storage

SMCS Code:

1000; 1404; 7002

If the engine will not be started for several weeks, the

lubricating oil will drain from the cylinder walls and

from the piston rings. Rust can form on the cylinder

liner surface. Rust on the cylinder liner surface will

cause increased engine wear and a reduction in

engine service life.
To help prevent excessive engine wear, use the

following guidelines:
• Complete all of the lubrication recommendations

that are listed in this Operation and Maintenance

Manual, “Maintenance Interval Schedule”

(Maintenance Section).

• If freezing temperatures are expected, check the

cooling system for adequate protection against

freezing. See this Operation and Maintenance

Manual, “Refill Capacities and Recommendations”

(Maintenance Section).

If an engine is out of operation and if use of the

engine is not planned, special precautions should be

made. If the engine will be stored for more than 1

month, a complete protection procedure is

recommended.
For more detailed information on engine storage, see

Special Instruction, SEHS9031, “Storage Procedure

For Caterpillar Products”.
Your Cat dealer can assist in preparing the engine for

extended storage periods.

SEBU8312-03

Operation Section

Lifting and Storage

Summary of Contents for TANVAC HDV3000










































































































































































































































































































































Search results

Summary of Contents for TANVAC HDV3000

Reviews:

Related manuals for TANVAC HDV3000

Brands by name

Popular brands

STG global TANVAC HDV3000, Operator'S Manual

Search results

Summary of Contents for TANVAC HDV3000

Reviews:

Related manuals for TANVAC HDV3000

Brands by name

Popular brands