manualshive.com logo in svg

Steris AMSCO 400 Series, Operator'S Manual

Share
Download
Steris AMSCO 400 Series Operator'S Manual Download Page 55

5-19

Component Identification

Operator Manual

P129394-020

The emergency stop switch should be pressed only in an
emergency 

situation such as

•

Safety mechanism fails to stop door when an obstruction is
present

•

Steam enters the chamber when the door is open 

NOTE: An alarm is generated when the emergency stop switch is
pressed. An emergency stop key is required to reset the switch.
Refer to alarm procedure to clear alarm.

5.11.1  Emergency Stop Key

An emergency stop key is required to reset the emergency stop
switch.

NOTE:  The emergency stop key should be retained by the
department supervisor.

Resetting the Switch:

1.

Insert emergency stop key.

2.

Turn emergency stop key counterclockwise.

a.

Alarm clears

b. Cycle aborts

c.

Sterilizer resumes normal operation

5.11.2  Emergency Stop

Guard

The emergency stop guard (see 

Figure

 

5-14

) helps prevent the

operator from accidentally pressing the emergency stop switch.

5.11.3  Emergency Stop Label

The emergency stop label is located above the emergency stop

switch (see 

Figure

 

5-14

 and 

Figure

 

5-16

).

Figure 5-16. Emergency Stop Label

Ä4GX

EMERGENCY STOP

PARO DE EMERGENCIA

ARRÊT D'URGENCE

!

Summary of Contents for AMSCO 400 Series















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands