manualshive.com logo in svg

Steris AMSCO 400 Series, Operator'S Manual

Share
Download
Steris AMSCO 400 Series Operator'S Manual Download Page 117

7-23

Cycle and Control Value Programming

Operator Manual

P129394-020

13. Review schedule. 

14. Edit if needed.

15. Press 

EXIT

 when done.

Utilities control is now programmed to turn sterilizer’s utilities on at
7:00 AM and off at 6:30 PM Monday through Friday. Saturday,
utilities turn on at 6:00 AM and off at 12:00 PM. Utilities are off all day
Sunday.

If sterilizer is equipped with optional integral steam generator,
generator flush cycle automatically runs 6:00 AM Monday through
Friday, 5:00 AM Saturday, and not at all Sunday.

Example #2:

 Some sterilizers are used multiple days without being

shut down. This sterilizer is to be used Monday morning at 5:00 AM
and not shut off until 8:00 PM Friday. Sterilizer is not used Saturday
or Sunday.

Steps to complete example schedule:

1.

At screen #20, press 

UTILITIES CONTROL

.

2.

At screen #39, press 

AUTOMATIC UTILITIES CONTROL

.

3.

At screen #34, press 

WEEKDAYS

.

4.

Enter restart time as “

1 2 0 0 AM

”. 

5.

Press 

SHUTOFF TIME

.

6.

At screen #33, press 

NONE

.

7.

At screen #34, press 

FRIDAY

.

8.

Press 

SHUTOFF TIME

 touchpad.

9.

At screen #33, enter 8:00 PM shut off time as “0 8 0 0 PM”. 

10. At screen #34, press 

MONDAY

.

11. Enter Restart time as “

0 5 0 0 AM

”. 

Figure 7-6. Scheduling Screen for Auto Utility Control

Example #2

Summary of Contents for AMSCO 400 Series















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands