Spokey 920883, User Manual

Page: 8 / 52

8
www.spokey.eu
www.spokey.pl
ASSEMBLY
PREPARATIONS
1. Before assembly make sure there is enough space.
2. Use the recommended tools.
3. Before assembly check if there are all the parts in the box.
It is recommended that product should be assembled by at least two people
to avoid injuries.
Most of the assembly equipment listed here has been packed separately,
but some elements come preassembled in certain assembly parts. If it is
required, dissassemble them and assemble again.
Read the instructions of all assembly steps and familiarize with all the
devices installed.
ASSEMBLY INSTRUCTIONS ( Drawings
– p.
46-48)
ATTENTION! Do not connect the device to the power source until you finish
the assembly.
STEP 1 Open the box, remove the parts. Place the main frame on the floor.
STEP 2 Lift the counter console (35) and place it in an upright position
together with the handles. Use the locking washers (64) and bolts M8*16
(51) to screw the console to the tops of the side columns.
STEP 3 Lift the columns and the counter console gently.
STEP 4 Fix the columns to the base: first screw the bolt M8*42 (70) with
the locking washer, next use the bolt M8*16 (51) with the washer (64).
Attention: to prevent the collapse of the console hold it while screwing.
STEP 5 Insert the water bottle grips (49) into the openings of the console
(35). Screw them with the bolt 4,2*12 (83).
STEP 6 Install the safety key.
FOLDING AND TRANSPORT OF THE TREADMILL
Don't try to move the treadmill if it's not folded and locked. Make sure that
the plug is disconnected from power supply.
To fold the treadmill, the running area must be raised with both hands until
a gentle signal is heard, informing that the treadmill has been correctly
locked in vertical position.
To assemble the treadmill, the coloured element on the piston situated
under the treadmill belt should be pressed with one foot, which will release
the lock. Next, the treadmill belt should be gently pulled down and the
operator should back 2 metres away from the treadmill as it will unfold automatically. Please refer to the drawing 1 (p. 49).
ATTENTION: Folded treadmill cannot be operated and utilized. Stop the
treadmill belt before folding the equipment. Folded treadmill should be
disconnected from power supply. Don't start the treadmill when it's folded.
To move the treadmill, raise it gently onto the rear transport rolls and move
it to the desired location, holding on both sides.
ATTENTION: Before transporting the treadmill make sure that it is
disconnected from power supply. The device should always be transported
by two persons..
MAINTANCE
Caution: before cleaning / lubrication you must take out the power plug from
a socket.
For cleaning the exercise machine, do not use any abrasive detergents.
Use a soft, damp cloth to remove dirt and dust.
The monitor (power supply dome) should be cleaned only with a dry cloth.
The equipment should be stored in dry places in order to protect it from any
moisture and corrosion.
Use a soft, damp cloth to wipe off the edges of the treadmill belt, and the
space between the treadmill belt and the frame edges. Clean the edge of
the belt on its bottom side also. Clean the upper part of the belt with a brush
and soap water once a month. NOTE: Before you start using the treadmill again, wait until the equipment
is completely dry.
Vacuum under the equipment at least once a month to prevent dust from
accumulating.
Once a year, it is recommended to remove the black cover of the engine in
order to remove any dust that may accumulate there.
NOTE: The level of equipment operational safety can be maintained only
by regular inspections checking for any damage and wear.
Connecting elements are the most vulnerable to any wear..
Track inclination angle setting
This model can manually adjust the inclination angle of the track.
To select your preferred angle (to choose from 3 degrees of inclination),
place one hand on the back of the main frame and lift it. Pull out the lock
from the angle adjuster with the other hand. Select the appropriate angle
and insert the lock into the adjuster. This will lock it in the correct position. WARNING! Make sure that both adjusters have the same angle. Use of a
track in which the adjusters are set at different angles can cause the track
to lose its stability, which can lead to injury.
Belt tension adjustment
Belt Tension Adjustment-It is very important for joggers and runners in
order to provide a smooth, steady running surface. Adjustment must be
made from the right and left rear roller in order to adjust tension with the
Hexagonal Wrench provided in the parts package. The adjustment bolt is
located at the end of the rails as noted in diagram below.
Note: Adjustment is thru the small holes on the end caps. Tighten the rear roller only enough to prevent slippage at the front roller.
Turn both the right and left bolt clockwise reasonably and inspect for proper
tension. When an adjustment is made to the belt tension, you must also
make a tracking adjustment to compensate for the change in belt tension.
DO NOT OVERTIGHTEN - Over tightening will cause belt damage and
premature bearing failure.
Belt tracking adjustment (picture, p. 49)
This treadmill is designed to keep the belt reasonably centred while in use.
It is normal for some belts to drift near one side while the belt is running
with no one on it. After a few minutes of use, the belt should have a
tendency to centre itself. If during use, the belt continues to move toward
one side, adjustments are necessary. The procedures are as below:
▲ First set speed at lowest position.
▲ Second check the belt shifts to which side. If the belt shifts to right, tighten the right bolt and loosen the left bolt by
using 6mm Hexagonal Wrench, until the belt is centered itself; if belt shifts
to left, tighten the left bolt and loosen the right bolt by using 6mm Hexagonal
Wrench, until the belt is centered. When adjusting the belt using the 6 mm
Hexagonal Wrenches, it is important to adjust the belt in half turn
increments. Over adjusting the belt can cause damage to the mat.
How to check the running mat for proper lubrication (picture, p. 49)

Disconnect the main power supply.

Fold the treadmill up into the storage position.

Feel the back surface of the running mat.
TREADMILL BELT