Spirit JOHNNY G SPIRIT BIKE Owner'S Manual Download Page 23

Page: 23 / 72

www.johnnygspiritbike.com

JOHNNY G SPIRIT BIKE

STEP FOUR

1. Thread

ADJUSTING AXLE (58)

through hole into

HANDLEBAR ANCHOR (51)

with

TWO

FLAT

WASHERS (121)

. Tighten fully, using

LEVER (67)

as a

tool if necessary.

NOTE: Gently pull on MAIN WIRE

(90) allowing space for insertion of ADJUSTING AXLE
(58) to prevent cable damage.

2. Insert a small Allen wrench into lever from bottom to

remove plastic cap at top of lever allowing access for
bolt installation

3. Install

LEVER (67)

in a 12 o’clock position. Attach

LEVER (67)

ADJUSTING AXLE (58)

using

BUTTON HEAD SOCKET BOLT (149)

using

4MM

ALLEN WRENCH (155).

4. Install plastic cap to seal lever.

HARDWARE FOR STEP 4

PART

TYPE

DESCRIPTION

QTY

ADJUSTING AXLE

SOCKET HEAD CAP BOLT

M3×P0.5×10L

121

FLAT WASHER

Ø1/4" × 13 × 1.0T

149

BUTTON HEAD SOCKET BOLT

M6 x 10L

Summary of Contents for JOHNNY G SPIRIT BIKE









































































Search results

Summary of Contents for JOHNNY G SPIRIT BIKE

Reviews:

Related manuals for JOHNNY G SPIRIT BIKE

Brands by name

Popular brands

Spirit JOHNNY G SPIRIT BIKE, Owner'S Manual

Search results

Summary of Contents for JOHNNY G SPIRIT BIKE

Reviews:

Related manuals for JOHNNY G SPIRIT BIKE

Brands by name

Popular brands