Spectra Logic T-Series Spectra T24 User Manual Download Page 12

Page: 12 / 103

Chapter 2. Library Overview

Library Layout

Library Front

The front of the Spectra T24 library provides access to the power button, the OCP and
its buttons, the front panel, the left and right magazines, the LEDs, and the mailslot.

Library Back

The back of the library provides access to SCSI connectors, tape drives, the power
connector, and Ethernet, serial, and USB ports.

Figure 2-1

The front of the Spectra T24 library.

Figure 2-2

The back of the Spectra T24 library, shown with two drives installed.

Power
Button

Air Vents

Right Magazine

OCP

Left Magazine

READY
LED

ERROR
LED

CLEAN
LED

ATTENTION
LED

Mailslot

UP
&
DOWN
Buttons

CANCEL
&
ENTER
Buttons

Fan

110/120 VAC

Power Inlet

68-pin SCSI
Connector Ports

Drive
Fans

Tape
Drives

USB Port
(Host)

Drive
LEDs

Ethernet Serial

Port

Drive
Handles

Summary of Contents for T-Series Spectra T24








































































































Search results

Summary of Contents for T-Series Spectra T24

Reviews:

Related manuals for T-Series Spectra T24

Brands by name

Popular brands

Spectra Logic T-Series Spectra T24, User Manual

Search results

Summary of Contents for T-Series Spectra T24

Reviews:

Related manuals for T-Series Spectra T24

Brands by name

Popular brands