Sony SRP-X500P Interface Manual Download Page 7

Page: 7 / 43

SRP-X500P RS-232C Interface Manual

Return packet format

When the SRP-X500P receives a command successfully, the parameter is returned together with an ACK
(0x41 (‘A’)) in the order shown below.

0x41

“

parameter” 0x0D

The parameter is the same as that of the AV/RGB INPUT SELECT command.

Example

When channel B input from among the AV/RGB INPUT connectors is selected
0x41 0x32 0x0D
(‘A 2 CR’)

2.1.3 INPUT FADER : 0x43 0x50 0x4D 0x35 (‘CPM5’)

This command is used to set the input fader setting.
The parameter set by this command works in the same way as the input fader setting in the OVER VIEW screen
of the SRP-X500P Manager.

Packet format

0x43 0x50 0x4D 0x35

“

parameter” 0x0D

♦

Parameter

The parameter consists of the 6 bytes of data in order as shown in the following table.

Byte Parameter

1st

MIC 1/WL 1 INPUT FADER

2nd

MIC 2/WL 2 INPUT FADER

3rd

MIC 3 INPUT FADER

4th

MIC 4 INPUT FADER

5th

LINE INPUT FADER

6th

AV/RGB INPUT FADER

Page 7/43

Summary of Contents for SRP-X500P












































Search results

Summary of Contents for SRP-X500P

Reviews:

Related manuals for SRP-X500P

Brands by name

Popular brands

Sony SRP-X500P, Interface Manual

Search results

Summary of Contents for SRP-X500P

Reviews:

Related manuals for SRP-X500P

Brands by name

Popular brands