background image

SRP-X500P RS-232C Interface Manual 

 

Example 

When the level meter readings are as follows: 
MIC 1/WL 1 INPUT LEVEL METER   

: Less than -30 [VU] 

MIC 2/WL 2 INPUT LEVEL METER   

: -30 [VU] 

MIC 3 INPUT LEVEL METER 

 

: -20 [VU] 

MIC 4 INPUT LEVEL METER 

 

: -15 [VU] 

LINE INPUT L LEVEL METER 

 

: -10 [VU] 

LINE INPUT R LEVEL METER 

 

: -8 [VU] 

AV/RGB INPUT L LEVEL METER 

 

: -7 [VU] 

AV/RGB INPUT R LEVEL METER   

: -6 [VU] 

SPEAKER OUTPUT 1 LEVEL METER 

: -5 [VU] 

SPEAKER OUTPUT 2 LEVEL METER 

: -4 [VU] 

SPEAKER OUTPUT 3 LEVEL METER 

: -3 [VU] 

SPEAKER OUTPUT 4 LEVEL METER 

: -2 [VU] 

LINE OUTPUT 1 LEVEL METER 

 

: -1 [VU] 

LINE OUTPUT 2 LEVEL METER 

 

: 0 [VU] 

LINE OUTPUT 3 LEVEL METER 

 

: 1 [VU] 

LINE OUTPUT 4 LEVEL METER 

 

: 2 [VU] 

 
0x41 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F 0x0D 
(‘A 0 1 2 3 4 5 6 7 8 9 : ; < = > ? CR’) 
 
 

2.2.3  STATUS REQUEST : 0x52 0x50 0x4D “specified value” 
(‘RPM“specified value”’) 

This command is used to acquire status information, such as the level meter value, from the SRP-X500P.

 

 

 

To acquire status of single item 

Transmit the following command to acquire the status of single item. 
 

 

Packet format 

0x52 0x50 0x4D “specified value” 0x0D 
 
Specify any single value that corresponds with the parameter in the following table.

 

 

 

Example 

To acquire the PROTECTION status: 
0x52 0x50 0x4D 0x71 0x0D 
(‘R P M q CR’) 
 

 

Return packet format 

When the SRP-X500P receives the command successfully, the parameter corresponding to the specified 
value is returned together with an ACK (0x41(‘A’)) in the order shown below. 
0x41 

parameter” 0x0D 

 
 
 

Page 23/43 

Summary of Contents for SRP-X500P












































Reviews: