Sony SRP-X500P Interface Manual Download Page 10

Page: 10 / 43

SRP-X500P RS-232C Interface Manual

Return packet format

When the SRP-X500P receives the command successfully, the parameter is returned together with an ACK
(0x41 (‘A’)) in the order shown below.
0x41

“

parameter” 0x0D

The parameter consists of 8 bytes of data and is the same as that of the OUTPUT FADER command.

2.1.7 REMOTE 1-6 LEVEL : 0x43 0x4C 0x56 0x4C (‘CLVL’)

This command is used to set the level of the REMOTE faders.
The level of the REMOTE faders are reset to 0 dB when the SRP-X500P is turned off.

Packet format

0x43 0x4C 0x56 0x4C

“

parameter” 0x0D

♦

Parameter

The parameter consists of 2 bytes of data in the order shown in the following table.

Byte Parameter

1st Channel

2nd LEVEL

•

Channel (1st byte)

Specifies the REMOTE fader channel.
The parameter and the REMOTE fader channel are as shown in the following table.

Channel

REMOTE 1

0x42 (‘B’)

REMOTE 2

0x43 (‘C’)

REMOTE 3

0x44 (‘D’)

REMOTE 4

0x45 (‘E’)

REMOTE 5

0x46 (‘F’)

REMOTE 6

0x47 (‘G’)

Page 10/43

Summary of Contents for SRP-X500P












































Search results

Summary of Contents for SRP-X500P

Reviews:

Related manuals for SRP-X500P

Brands by name

Popular brands

Sony SRP-X500P, Interface Manual

Search results

Summary of Contents for SRP-X500P

Reviews:

Related manuals for SRP-X500P

Brands by name

Popular brands