Sony SRP-X500P Interface Manual Download Page 27 | Manualshive

Page: 27 / 43

background image

SRP-X500P RS-232C Interface Manual

♦

INPUT LEVEL (16th-21st byte)

Shows the value indicated by the yellow triangular marker at the side of the input fader in the OVER
VIEW screen of the SRP-X500P Manager. This value is calculated using the input volume parameter,
input fader parameter, master volume level parameter, and remote fader 1-6 parameters and this
indicates the total input level value.

The INPUT LEVEL parameter consists of the 6 bytes of data in the order shown in the following table.

Byte Parameter

1st

MIC 1/WL 1 INPUT LEVEL

2nd

MIC 2/WL 2 INPUT LEVEL

3rd

MIC 3 INPUT LEVEL

4th

MIC 4 INPUT LEVEL

5th

LINE INPUT LEVEL

6th

AV/RGB INPUT LEVEL

The correspondence of the parameter with the level setting is the same as that of the FADER
parameter of the INPUT FADER command (page 7).

♦

OUTPUT LEVEL (22nd-29th byte)

Shows the value indicated by the yellow triangular marker at the side of the output fader in the OVER
VIEW screen of the SRP-X500P Manager. This value is calculated using the output fader parameter,
master volume level parameter, and remote fader 1-6 parameter. This value is an indication of the total
input level value.

The OUTPUT LEVEL parameter consists of 8 bytes of data in the order shown in the following table.

Byte Parameter

1st

SPEAKER OUTPUT 1 LEVEL

2nd

SPEAKER OUTPUT 2 LEVEL

3rd

SPEAKER OUTPUT 3 LEVEL

4th

SPEAKER OUTPUT 4 LEVEL

5th

LINE OUTPUT 1 LEVEL

6th

LINE OUTPUT 2 LEVEL

7th

LINE OUTPUT 3 LEVEL

8th

LINE OUTPUT 4 LEVEL

The correspondence of the parameter with the level setting is the same as that of the FADER
parameter of the INPUT FADER command (page 7).

♦

INPUT MUTING (30th byte)

Shows the muting status of the input channels in the form of 8 bits data.
The bit is 0 for a channel which is not turned off (

“

Muting off”) and 1 for a channel which is turned

off (

“

Muting on”).

MSB

LSB

bit7 bit6 bit5

bit4 bit3 bit2 bit1 bit0

0

1

AV/RGB

LINE

MIC 4 MIC 3 MIC 2 MIC 1

/WL 2 /WL 1

Page 27/43

«
...
25
26
27
28
29
...
»

Summary of Contents for SRP-X500P












































Reviews:

No comments

Related manuals for SRP-X500P

AZ8350 - Cd Radio Cass Recorder

Brand: Magnavox Pages: 18

Brand: SAL Pages: 21

Brand: Devine Pages: 15

Brand: Pyle Pages: 12

Brand: WOXTER Pages: 36

Brand: Yealink Pages: 2

Brand: ELBE Pages: 19

Brand: Mainlink Pages: 46

JBL QUANTUM Stream Talk

Brand: Harman Pages: 15

Brand: Iluv Pages: 36

Brand: Hitachi Pages: 16

Brand: Hitachi Pages: 15

Brand: Hitachi Pages: 18

Brand: Hitachi Pages: 33

Brand: Hitachi Pages: 25

Brand: Hitachi Pages: 22

Brand: Hitachi Pages: 44

Brand: Hitachi Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands