SOMFY Freevia 280 Operating And Installation Manual Download | Manualshive

Page: 18 / 37

background image

16

EN

operation in sequential mode

Successive presses of the same control button will lead to the following movements of the

motor:

open, stop, close, stop, open etc.

oPEraTioN

1m

complete opening of the gate

by

pressing button 1.

open the gate completely

by pressing

button 1.

Partial opening

of the gate (approx 1 m)

by pressing the activated button.

complete opening

►

Pedestrian opening

►

close

the gate by pressing the activated

button.

close

the gate by pressing button 1

again.

stop

the gate when moving by pressing

button 1 again.

Pedestrian opening is achieved by pressing a button on the remote control that

requires prior activating (see p. 20).

«
...
16
17
18
19
20
...
»

Summary of Contents for Freevia 280






































Reviews:

No comments

Related manuals for Freevia 280

Brand: WALKY Pages: 12

Brand: CAB Pages: 15

Brand: SOMFY Pages: 4

8550WRGD Admiral II

Brand: Raynor Pages: 44

Brand: Ryobi Pages: 168

Brand: BFT Pages: 14

Brand: Aprimatic Pages: 16

Brand: Automatismos Pujol Pages: 24

Brand: Automatic Technology Pages: 38

GDO-8V2 EasyRoller II

Brand: Automatic Technology Pages: 24

Brand: Automatic Technology Pages: 24

CONDOR 500 / ONE

Brand: Comunello Pages: 34

X-pervisio 1000

Brand: Visonic Pages: 12

Brand: Alutech Pages: 96

Brand: tau Pages: 40

Brand: Dea Pages: 108

Brand: Chamberlain Pages: 32

Brand: Eagle Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands