37
environment it is especially recommended that the unit is protected with anti-corrosion products for the purpose,
especially between working periods. As a suggestion we advise the application of graphited greases suitable for high
temperature lubrication function and anti-corrosion protection.
3.7 In the Products belonging to the pellet range, in addition to the daily and weekly maintenance detailed in the
instruction manual, it’s also required to clean its interior and the respective fume extraction chimney. These tasks must
be performed every 600-800 kg of pellets consumed in the case of pellet stoves (air and water) and compact boilers, and
every 2000-3000 kg of pellets consumed in the case of automatic boilers. In case these quantities are not consumed, at
least a systematic preventive maintenance on an annual basis must be done.
3.8 It is up to the Buyer to ensure that periodic maintenances are performed as indicated in the manuals and handling
instructions accompanying the product. Whenever requested it must be proven by the presentation of the technical report
of the entity responsible for it, or alternatively by registering them in the instruction manual in the dedicated section.
3.9 To prevent damage to the equipment due to overpressure, it must be assured, in the installation, safety elements
such as pressure relief valves or temperature pressure, if applicable, as well as expansion tank adjusted to the
installation, to assure its proper operation. Please note that: the referenced valves should have a value equal to or less
than the pressure supported by the equipment; there may not be any shut-off valve between the equipment and the
respective safety valve; a preventive maintenance plan should be provided to certify the correct functioning of these
security features; regardless of device type, all safety valves should be channeled into sewer siphon, to prevent damage
to housing by discharges of water. The Product Warranty does not cover damage caused by improper channeling water
discharged by the valves.
3.10 To prevent damage by galvanic corrosion to the equipment and the attached piping, it is recommended the use of
dielectric tabs (cuffs) on connections between the device and metal tubes, whose characteristics potentiate this kind of
corrosion. The Product Warranty does not cover damages caused by the non-use of such dielectric spacers.
3.11 The water or thermal fluid used in the heating system (Hydro stoves, boilers, fireplaces central heating, etc.) must
comply with the legal requirements and ensure the following physical-chemical characteristics: absence of suspended
solids; low conductivity; Residual hardness of 5 to 7 (ºF) French degrees; neutral pH close to 7; low concentration
chlorides and iron; no air inlets by depression or other. If the installation enhances a water automatic make-up it should
consider upstream, a preventive treatment system consisting of filtration, water softening and preventive dosage of
polyphosphates (fouling and corrosion) as well as a deaeration step, in case this is necessary . If in some circumstances
some of these indicators present values outside the recommended, the warranty will cease its effect.
3:12 Except as expressly provided by law, an intervention in warranty does not renew the Product warranty period. The
rights of warranty are not transferable to the purchaser of the product.
3.13 The equipment must be installed in accessible local and without risk to the technician. The means necessary for
access to the equipment will be provided by the Buyer, as well as all the charges resulting from the process.
3.14 Guarantee is valid for products and equipment sold by Solzaima SA only and exclusively within the geographical
and territorial area of the country where the Product was sold by Solzaima.
4. Circumstances that exclude the application of Warranty
The following cases are excluded from Warranty, being the total cost of the reparation payable by Buyer:
4.1. Maintenance operations, tuning of the product, start-ups, cleaning, elimination of errors or anomalies that are not
related to deficiencies of equipment components and replacement of batteries;
4.2. Components in direct contact with fire such as: vermiculite supports, baffle or protection plates, vermiculite, sealing
cords, burners, ash pans, trim wood, smoke regulators, ash grid, whose wear is directly related to the operating
conditions. Paint degradation, as well as its degradation by corrosion due to fuel excess charge, open drawer use or
excessive draft of the chimney installation. The glass breakage by improper handling or other reasons unrelated with the
conformity of the
product. In the pellets family equipment’s, the combustion igniter it’s a wearing part, for that reason this
component only as 6 moth of warranty;
4.3. Wear components such as bearings;
Summary of Contents for TEK Basic
