Solar Stik PSS-G Deployment Manual Download Page 42 | Manualshive

Page: 42 / 141

background image

PSS-G/RAID Alternative Energy System Deployment Guide

August 2020

|

Solar Stik

®

Inc.

42

|

PRO-Verter

7000 AGS (side view)

Power Hub 2400 (side view)

Power Hub 2400 (side view)

The photos below show how all of the components will look when they are arranged as in the
configuration described in the diagrams in Step 2.

Connect all seven (7) Expander Paks to the two (2) Inter-Connect Strips using seven (7) 5’ Inter-
Connect Cables. Place/stow the Inter-Connect Strips on the second level as shown in the diagram
below. This location protects the Inter-Connect Strips from the environment.

3 Connect Expander Paks to Inter-Connect Strips

Figure 22. Connect Expander Paks using Inter-Connect Strips and leashes and stow the Inter-Connect Strips

Inter-Connect Strip

Inter-Connect Strip

Li Expander Pak 2400 (x4)

Li Expander Pak 2400 (x3)

«
...
40
41
42
43
44
...
»

Summary of Contents for PSS-G














































































































































Reviews:

No comments

Related manuals for PSS-G

Brand: Srne Pages: 38

Brand: Cypress Pages: 12

Brand: Viking Pages: 4

Brand: Black Box Pages: 16

Brand: Extron electronics Pages: 8

SINUS CABINET K Series

Brand: Elettronica Santerno Pages: 226

Brand: Harman Kardon Pages: 16

Brand: Cable-Tronix Pages: 4

Brand: Zamp Solar Pages: 9

Brand: Thor Broadcast Pages: 9

Brand: Wavecrest Pages: 39

Brand: LC Pages: 44

USB 2.0 Video Capture Device

Brand: SIIG Pages: 12

Brand: Tektronix Pages: 188

Brand: Teracue Pages: 38

Brand: Lantronix Pages: 24

Brand: Infotel Pages: 9

Brand: Crestron Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands