Solar-Log 1200 User Manual Download Page 60

Page: 60 / 158

Notifications

Fig.: Performance Monitoring with notification and inverter

Inverter 1, Inverter 1 house

Inverter 2, Inverter 2

house

Generator Power=

5500 Wp

3300 Wp

Current power output

= 3950 W

= 2950 W

Current efficiency

= 71.81 %

= 89.39 %

Inverter with a deviation

Reference Inverter

Inverter has generated the most power with its value of 0.8939 and is thus used as the

Reference Inverter.

3.2.2 Calculation and Explanation of the Notification

In regard to the reference inverter, inverter 1 is compared to all of the inverters in the same module field (in

the example only output is used).

A deviation of 19.65% is determined based on the comparison of the generator capacity and IRV forecast.

Calculating the Deviation for Inverter 1

Deviation Calculation

Inverter 1 IRV calculation

(5500 x 89.39)100= IRV 4916 W

Efficiency of Inverter 1

(3950 W: 5500 W)* 100= 71.81%

This corresponds to 71.81 % of the generator power or a value of 0.7181 kWp.

Deviation as a percentage

IRV Inverter 1 - IAV Inverter 1

4916 W -3950 W= 966 W

Deviation as a percentage

(966 W: 4916 W)* 100= 19.65 %

Inverter 2 is used as the reference inverter since it was the most effective one at the time of the measure-

ment. Inverter 1 should have produced an output of 4916 W based on the measurement and the calcula-

tions comparing all of the inverters in the same module field. The actual output was 3950 W, a deviation of

19.65%. This caused a notification to be sent.

Summary of Contents for 1200































































































































































Search results

Summary of Contents for 1200

Reviews:

Related manuals for 1200

Brands by name

Popular brands

Solar-Log 1200, User Manual

Search results

Summary of Contents for 1200

Reviews:

Related manuals for 1200

Brands by name

Popular brands