socomec SUNSYS - B10 Installation And Operation Manual Download Page 32 | Manualshive

Page: 32 / 54

socomec SUNSYS - B10 Installation And Operation Manual Download Page 32

32

Once entered into the reactive power managing menu is possible to:
1.

Reactive Power Mode: by pre

ssing “OK” is possible to enable one of the four management arrangement

of reactive power, or disable it.

Select the desired function by pressing “

↓

” o “

↑

” and confirm pressing “OK”.

2.

Const. PF: by pressing “OK” is possible to set the parameter of constant power factor function.

Select the desired value

by pressing “

↓

” o “

↑

” and confirm pressing “OK”.

3.

Const Q: by pressing “OK” is possible to set the parameter of constant reactive power function.

Select the desired value by pressing “

↓

” o “

↑

” and confirm pressing “OK”.

4.

Curve PF(P): by pres

sing “OK” is possible to set the parameters of curve of management of the power

factor in function of active power.

Reactive Power Mode

Const. PF

Const. Q

Curve PF (P)
Curve Q (U)

Reactive Power Mode

<Off>

Const. Power Factor

<-0.90pf>

Const. Reactive Power

<+0VAR>

«
...
30
31
32
33
34
...
»

Summary of Contents for SUNSYS - B10























































Reviews:

No comments