background image

- 6 - 

 

 

[Compliance Requirements] 

This product has been confirmed to comply with Japanese laws only. 

When the product is exported, strictly follow all national and regional laws and regulations in Japan 
and the countries it is exported to. 

 

When the battery is prepared by the customer, the battery specifications, selection and product 

performance are the responsibility of the customer. Please note the following points for use.   

This product requires a nickel metal-hydride battery. 

 
Under UN restrictions, nickel metal hydride batteries are classed as dangerous (Class 9) for sea 
transport only. *This product is a non-dangerous article for sea transport (as of August 2012). 

 

When transporting a nickel-metal hydride battery or equipment containing nickel-metal hydride 
battery by a means subject to the UN Regulations, it is necessary to satisfy the UN 
Recommendations on the Transport of Dangerous Goods, Technical Instructions (ICAO-TI) of the 
International Civil Aviation Organization (ICAO), and International Marine Dangerous Goods 
Code (IMDG Code) of the International Maritime Organization. When the product is transported 
by the user, it is necessary for the user themselves to confirm and conform to the latest 
standards and laws of the corresponding country related to transportation.

   

 

Summary of Contents for LECP7-XB54 Series













































Reviews: