Skyjack SJ-7027 Operating, Maintenance And Parts Manual Download Page 75

Page: 75 / 216

SECTION 4, Page 4

SJ-600 Series Engine Powered

112715

June 2001

ELECTRICAL SYSTEM

TROUBLESHOOTING INFORMATION

CHOKE INOPERATIVE
FROM PLATFORM OR
ENGINE CONTROLS
(Dual Fuel)

ENGINE CRANKS BUT
WILL NOT START
(Continued)

16. Loose or broken wire #11 from fuel

valve (2G11) to fuel pump (FP1).

17. Defective fuel pump (FP1) (Gasoline

Only).

18. Open diode (D57) from starter motor

to ignition coil.

19. Choke inoperative (Dual Fuel).

20. Defective glow plugs (Diesel).

21. No spark (Dual Fuel).

1. Engine oil lever low.

2. Engine overheated.

3. Defective temperature switch (TPS1).

4. Defective oil pressure switch (OPS1).

5. Loose or broken wire #2B from oil

pressure switch (OPS1) to

temperature switch (TPS1).

6. Loose or broken wire #2A from relay

(10BCR2) to oil pressure switch

(OPS1).

7. Loose or broken wire #10B from base

terminal block to relay (10BCR2).

8. Loose or broken wire #10A from base

terminal block to relay (10BCR2).

9. Loose or broken wire #37 from relay

(10BCR2) to ignition coil (Dual fuel).

or diesel valve solenoid (2D37)

(Diesel).

10. Defective relay (10BCR2).

1. Loose or broken wire #31A from

choke switch (S31) to choke solenoid

(CS31A).

2. Defective choke solenoid (CS31A).

1. Loose or broken wire #10 from key

select switch (S3) to choke switch

(S13).

2. Defective choke switch (S13).

3. Loose or broken wire #31 from choke

switch (S13) to choke relay (31CR).

4. Loose or broken wire #02 from relay

(31CR) to base terminal block (TB1).

5. Loose or broken wire #05 from base

terminal block (TB1) to relay (31CR).

6. Loose or broken wire #31A from relay

(31CR) to base terminal block (TB1).

7. Loose or broken wire #31A from base

terminal block (TB1) to choke

solenoid (CS31A).

8. Defective choke relay (31CR).

16. Check continuity. Replace if

defective.

17. Check pump. Replace if defective.

18. Check diode. Repair if necessary.

19. Check choke. Repair if necessary.

20. Check glow plugs. Repair if

necessary.

21. Refer to engine manufacturer

service manual.

1. Refill to proper level.

2. Check cooling system.

3. Check switch. Replace if defective.

4. Check switch. Replace if defective.

5. Check continuity. Replace if

defective.

6. Check continuity. Replace if

defective.

7. Check continuity. Replace if

defective.

8. Check continuity. Replace if

defective.

9. Check continuity. Replace if

defective.

10. Check relay. Replace if defective.

1. Check continuity. Replace if

defective.

2. Check solenoid. Replace if

defective.

1. Check continuity. Replace if

defective.

2. Check switch. Replace if defective.

3. Check continuity. Replace if

defective.

4. Check continuity. Replace if

defective.

5. Check continuity. Replace if

defective.

6. Check continuity. Replace if

defective.

7. Check continuity. Replace if

defective.

8. Check relay. Replace if defective.

ENGINE STARTS BUT
WILL NOT CONTINUE
RUNNING

TROUBLE

PROBABLE CAUSE

REMEDY

CHOKE INOPERATIVE
FROM PLATFORM
(Dual Fuel)

Summary of Contents for SJ-7027

























































































































































































































Search results

Summary of Contents for SJ-7027

Reviews:

Related manuals for SJ-7027

Brands by name

Popular brands

Skyjack SJ-7027, Operating, Maintenance And Parts Manual

Search results

Summary of Contents for SJ-7027

Reviews:

Related manuals for SJ-7027

Brands by name

Popular brands