Skyjack SJ-7027 Operating, Maintenance And Parts Manual Download Page 154

Page: 154 / 216

SECTION 6, Page 67

SJ-600 Series Engine Powered

112715

June 2001

Index

No.

Skyjack

Part No.

Description

Units

per

Assy.

900550

CENTER DRIVE Assembly

121629

CAP, Output Shaft (2WD)

900329

• BOLT, M8X1.25X15

900328

• SEAL, Lip

900427

• FLANGE, Output Shaft

900490

• O-RING, Flange

900408

• HOUSING, Transfer Case, Front

900080

• PIN, Dowel

900321

• BEARING, 6210

900547

• GEAR, Input Shaft

121554

• Assembly, Output Shaft and Gear

900407

• HOUSING, Transfer Case, Rear

900071

• PLUG, Oil Drain

900283

• BOLT, M8X1.25X50

900072

• SEAL, Drain Plug

900650

• MAGNET, Ring

900643

• PLUG, Oil Drain

900370

• BREATHER

900553

• FITTING, 90°

900336

• FLANGE, Hydraulic motor

900414

• SHIM

900025

• BOLT, M8X1.25x22

114126

PLATE, Center Drive Motor Cover And Hose Bracket

109311

MOTOR, 2 Speed drive

103623

• VALVE, Series/parallel

355113

• MANIFOLD, Motor

103613

• COIL, Series/parallel valve

115340

• CHECK BALL

115338

• SEAL KIT

(Ref.)

HARDWARE, Drive Motor Mounting

103910

• BOLT, 1/2”-13 x 1.25” Grade 8 (Use Loctite

242 or eq

uivalent)

103470

• WASHER, 1/2” Lock

105863

KIT, Universal joint

121585

SHAFT, Rear drive

103099

YOKE

900542

• BOOT, Output Shaft

Following items are used on 4WD machines

103099

YOKE

900542

• BOOT, Output Shaft

105863

KIT, Universal joint

111544

SHAFT, Front drive

103084

U-BOLT KIT

900655

KIT, SERVICE (9 Pieces)
(Consists of items 3(3), 5(3), 14(2) & 17(1))

FIGURE 6-23B. CENTER DRIVE AND DRIVE SHAFTS

(Haessler Drive Serial # 1690 and Below)

Summary of Contents for SJ-7027

























































































































































































































Search results

Summary of Contents for SJ-7027

Reviews:

Related manuals for SJ-7027

Brands by name

Popular brands

Skyjack SJ-7027, Operating, Maintenance And Parts Manual

Search results

Summary of Contents for SJ-7027

Reviews:

Related manuals for SJ-7027

Brands by name

Popular brands