Skyjack SJ-7027 Operating, Maintenance And Parts Manual Download Page 73

Page: 73 / 216

SECTION 4, Page 2

SJ-600 Series Engine Powered

112715

June 2001

ELECTRICAL SYSTEM

5. Platform/base select switch (S10) set

to base position.

6. Open or defective platform/base

select switch (S10).

7. Loose or broken wire #7A from

platform/base select switch (S10) to

platform emergency stop switch (S4).

8. Open or defective platform

emergency stop switch (S4).

1. Open or defective emergency stop

switch (S4).

2. Loose or broken wire #08 from

emergency stop switch (S4) to off/

lift/drive select switch (S3).

3. Open or defective off/lift/drive select

switch (S3).

1. Open or defective key select switch

(S3).

2. Loose or broken wire #10 from key

select switch (S3) to start switch

(S15).

3. Defective start switch (S15).

4. Loose or broken wire #32 from start

switch (S15) to relay (32CR).

5. Defective relay (32CR).

6. Loose or broken jumper wire #41 on

relay (32CR).

7. Loose or broken wire #02 from relay

(32CR) to base terminal block.

8. Loose or broken wire #05 from base

terminal block to relay (32CR).

9. Loose or broken wire #32A from

relay (32CR) to base terminal block.

10. Loose or broken wire #32A from

base terminal block to starter

contactor (32ACR).

11. Defective starter contactor (32ACR).

12. Loose or broken wire #00 from

starter contactor (32ACR) to base.

13. Loose or broken wire #103 from

main power disconnect (S1) to starter

contactor (32ACR).

14. Loose or broken wire #104 from

starter contactor (32ACR) to starter

motor.

15. Defective starter motor.

1. Loose or broken wire #05 from base

terminal block to engine off/on switch

(S30).

5. Set (S10) to platform position.

6. Check switch. Replace if defective.

7. Check continuity. Replace if

defective.

8. Check switch. Replace if defective.

1. Check switch. Replace if defective.

2. Check continuity. Replace if

defective.

3. Check switch. Replace if defective.

1. Check switch. Replace if defective.

2. Check continuity. Replace if

defective.

3. Check switch. Replace if defective.

4. Check continuity. Replace if

defective.

5. Check relay. Replace if defective.

6. Check continuity. Replace if

defective.

7. Check continuity. Replace if

defective.

8. Check continuity. Replace if

defective.

9. Check continuity. Replace if

defective.

10. Check continuity. Replace if

defective.

11. Check contactor. Replace if

defective.

12. Check continuity. Replace if

defective.

13. Check continuity. Replace if

defective.

14. Check continuity. Replace if

defective.

15. Check motor. Repair or replace if

defective.

1. Check continuity. Replace if

defective.

TROUBLESHOOTING INFORMATION

ALL FUNCTIONS
INOPERATIVE FROM
PLATFORM

ENGINE WILL NOT
CRANK FROM
PLATFORM

TROUBLE

PROBABLE CAUSE

REMEDY

NO POWER TO
PLATFORM
(Machines With Base
Control Box Option)
(Continued)

ENGINE WILL NOT
CRANK FROM ENGINE
CONTROLS

Summary of Contents for SJ-7027

























































































































































































































Search results

Summary of Contents for SJ-7027

Reviews:

Related manuals for SJ-7027

Brands by name

Popular brands

Skyjack SJ-7027, Operating, Maintenance And Parts Manual

Search results

Summary of Contents for SJ-7027

Reviews:

Related manuals for SJ-7027

Brands by name

Popular brands