Skyjack SJ-7027 Operating, Maintenance And Parts Manual Download Page 22 | Manualshive

Page: 22 / 216

background image

SECTION 2, Page 11

SJ-600 Series Engine Powered

June 2001

Hydraulic Generator (Option)

1.

To start the hydraulic generator,

Ensure the

engine is on high throttle by selecting “HIGH”
on the “Low/High Throttle Select” switch.

Select

the “LIFT” position with the “Off/Lift/Drive” key
switch, then depress hydraulic generator push-
button on the side of the operator’s control box.
The push-button will illuminate and generator
on base will start. To restore normal operation,
depress push-button again. The light in push-
button will go out and the generator will turn off.

Note

While hydraulic generator push-button switch light is
illuminated, the lift and drive circuits in the Operator’s
Control Box are cut out.

Electrical Inverter (Option)

1.

Turn the main disconnect switch to the “ON”
Position.

2.

Turn the “ON/OFF” switch located on the front
face of the inverter to the “ON” Position.

3.

Start the machine and turn the throttle switch to
the high idle setting.

4.

Inverter activation is indicated by a glowing green
LED on the front face of the inverter.

5.

To turn off the inverter, shut down the platform
engine and/or slide the “ON/OFF” switch on the
inverter to the “OFF” position.

Note

The inverter will only supply power to the platform
when the engine is running and the throttle switch is
set to the HIGH idle position. Deselecting the high idle
throttle setting or stopping the engine will turn the
inverter off.

1

2

3

Winching And Towing Procedures

Warning

When Towing,

DO NOT

drive onto a downward slope

or brake the towing vehicle rapidly.

Parking Brake System

Figure 2-13. Disc Parking Brake

1 - 3.

Parking Brake Disc

-This device disengages

the

brake disc(1)

when driving forward or in reverse. A

hydraulic brake cylinder(2)

, linked to a

disc

caliper(3)

, engages and disengages a brake disc on

the rear axle drive shaft yoke. The brake MUST be
manually disengaged for pushing, towing or winching.

DO NOT

push or tow the work platform onto a

downward slope or pull the platform down an incline
towards the winch.

The special procedure for

manually disengaging the parking brake is as follows:

Warning

DO NOT

manually disengage the parking brakes if

the work platform is on a slope.

«
...
20
21
22
23
24
...
»

Summary of Contents for SJ-7027

























































































































































































































Reviews:

No comments

Related manuals for SJ-7027

Brand: Sunshine Pages: 19

Brand: RUDETRANS Pages: 31

Brand: Upright Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands