manualshive.com logo in svg

Skyjack SJ-7027, Operating, Maintenance And Parts Manual

The Skyjack SJ-7027 is a versatile aerial work platform renowned for its outstanding performance and durability. Ensure seamless operation and longevity with our comprehensive Operating, Maintenance, and Parts Manual. Download this essential manual for free at manualshive.com and unlock the full potential of your Skyjack SJ-7027.

Share
Download
background image

SECTION 2, Page 6

SJ-600 Series Engine Powered

June 2001

Operating Procedures

The following descriptions are for Operating
Procedures.  A qualified operator 

MUST 

read and

completely understand these descriptions before
operating this work platform.

Set-Up Procedure

1.

Remove all packing materials and inspect for
damage incurred during transport.  This is
normally required for equipment being put into
service for the first time, after the equipment has
been unloaded.

Note

Report any damage to delivery carrier immediately.

2.

Inspect work platform thoroughly and remove
any foreign objects.

3.

Raise the side, extension platform (if so
equipped), and gate railings to their upright
position and lock in place with locking pins.
Lock side railings to front railings with locking
pins.

4.

Remove the operator’s control box from its
shipping container and secure it to the railing at
the right front of the platform.  Attach the control
cable and power deck extension cable (if so
equipped) to the scissor’s control cable.

5.

Open the fuel tank side cabinet door.  Fill the
fuel tank to “F” level on fuel gauge with the
proper fuel. (Refer to decal on fuel tank)

6.

Close the fuel tank side cabinet door.

7.

Machines with Dual Fuel:
Make sure propane hose coupler is properly
secured at propane cylinder and valve on
propane cylinder is opened all the way.

8.

Open the hydraulic tank side cabinet door.
Check the hydraulic oil level (scissors must be
fully lowered) in the tank.  Level should be at or
slightly above the top mark on the sight glass. If
required, add a quality grade hydraulic oil such
as ATF Dexron III (ESSO).

9.

Check the battery fluid level.  If fluid level is not
at FULL mark on battery, add distilled or
demineralized water only.

 

Warning

Explosion Hazard

Keep flames and sparks away.  

DO NOT

 smoke near

batteries.

First Aid

Immediately flush eyes with cold water if electrolytic
acid is splattered into them.  Seek medical attention.

10. Move the work platform to a level, firm test area

where the work platform can be vertically
extended to its maximum working height.  If the
work platform is to be pushed, towed or winched,
ensure that the parking brake has been
disengaged.  

When pushing, towing or

winching, 

DO NOT

 exceed 2 mph (3.2 kph).

Using the Base Controls:

11. Turn the Emergency Power Disconnect Switch

to “ON” position.

Using the Platform Controls:

12. Pull out the Emergency Stop Button.

Note

Engine will not start unless this button is in the
“ON” position.

13. Insert key into Off/Lift/Drive Select Key Switch

and turn to “LIFT” position.

Note

Start engine in low throttle position.

Using the Engine Controls on the Engine:

14. Pull Engine Off/On Switch plunger out.

15. Select desired fuel source with Fuel Select

Switch. (Gasoline engines with dual fuel)

Note

Refer to label on inside of engine front guard for
fuel switch sequence.

16. Depress and hold the Choke Push-Button.

(Gasoline engines)  Depress and hold Glow Plug
Push-Button for 15 to 20 seconds. (Diesel
engines)

Summary of Contents for SJ-7027

























































































































































































































Reviews:

No comments

Related manuals for SJ-7027

Skyjack SJII 3015 Operating Manual preview
SJII 3015
Brand: Skyjack Pages: 49
Terex Z-33 Operator'S Manual preview
Z-33
Brand: Terex Pages: 58
Terex GS69F-18000 Operator'S Manual preview
GS69F-18000
Brand: Terex Pages: 59
Kleton MJ525 Instruction Manual preview
MJ525
Brand: Kleton Pages: 5
Kleton MJ524 Instruction Manual preview
MJ524
Brand: Kleton Pages: 5
Kleton MJ522 Instruction Manual preview
MJ522
Brand: Kleton Pages: 5
Kleton MJ520 Instruction Manual preview
MJ520
Brand: Kleton Pages: 5
Kleton MJ521 Instruction Manual preview
MJ521
Brand: Kleton Pages: 5
Mec Micro 19 Service & Parts Manual preview
Micro 19
Brand: Mec Pages: 84

Brands by name

Popular brands

Load more brands